- CentOS 4.0/IA64 を 俺私物の hp workstation zx2000 に入れました。
恒例のdmesgは以下。
Linux version 2.6.9-5.0.3.101.EC (builder@wm) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Sat Feb 26 16:18:51 EET 2005
EFI v1.10 by HP: SALsystab=0x3ff88000 ACPI 2.0=0x3fdf7000 SMBIOS=0x3ff8a000 HCDP=0x3fdf6000
booting generic kernel on platform hpzx1
PCDP: v0 at 0x3fdf6000
ACPI: RSDP (v002 HP ) @ 0x000000003fdf7000
ACPI: XSDT (v001 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdf702c
ACPI: FADT (v003 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfdd00
ACPI: SPCR (v001 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfde38
ACPI: DBGP (v001 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfde88
ACPI: MADT (v001 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfdf48
ACPI: SPMI (v004 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfdec0
ACPI: CPEP (v001 HP zx2000 0x00000000 HP 0x00000000) @ 0x000000003fdfdf10
ACPI: SSDT (v001 HP zx2000 0x00000006 INTL 0x02012044) @ 0x000000003fdfb680
ACPI: SSDT (v001 HP zx2000 0x00000006 INTL 0x02012044) @ 0x000000003fdfbcf0
ACPI: SSDT (v001 HP zx2000 0x00000006 INTL 0x02012044) @ 0x000000003fdfd460
ACPI: SSDT (v001 HP zx2000 0x00000006 INTL 0x02012044) @ 0x000000003fdfd690
ACPI: DSDT (v001 HP zx2000 0x00000007 INTL 0x02012044) @ 0x0000000000000000
Warning: acpi_table_parse(ACPI_SRAT) returned 0!
Warning: acpi_table_parse(ACPI_SLIT) returned 0!
efi.trim_top: ignoring 4KB of memory at 0x0 due to granule hole at 0x0
efi.trim_top: ignoring 636KB of memory at 0x1000 due to granule hole at 0x0
efi.trim_bottom: ignoring 15360KB of memory at 0x100000 due to granule hole at 0x0
Initial ramdisk at: 0xe00000003e75e000 (2808275 bytes)
SAL 0.20: INTEL MSL REF SAL version 1.60
SAL: AP wakeup using external interrupt vector 0xff
ACPI: Local APIC address c0000000fee00000
GSI 47 (level, low) -> CPU 0 (0x0000) vector 48
1 CPUs available, 1 CPUs total
MCA related initialization done
Virtual mem_map starts at 0xa0007fffffc80000
On node 0 totalpages: 63397
DMA zone: 63397 pages, LIFO batch:4
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: BOOT_IMAGE=scsi0:EFI\redhat\vmlinuz-2.6.9-5.0.3.101.EC root=/dev/VolGroup00/LogVol00 rhgb quiet ro
PID hash table entries: 2048 (order: 11, 65536 bytes)
CPU 0: base freq=200.000MHz, ITC ratio=9/2, ITC freq=900.000MHz+/-450ppm
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 6, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 5, 524288 bytes)
Memory: 1004544k/1014352k available (5463k code, 20656k reserved, 2205k data, 384k init)
Leaving McKinley Errata 9 workaround enabled
Calibrating delay loop... 1347.52 BogoMIPS (lpj=657408)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 1024 (order: 0, 16384 bytes)
Boot processor id 0x0/0x0
task migration cache decay timeout: 10 msecs.
Brought up 1 CPUs
Total of 1 processors activated (1347.52 BogoMIPS).
checking if image is initramfs... it is
Freeing initrd memory: 2720kB freed
NET: Registered protocol family 16
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOSAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
ACPI: PCI Interrupt Routing Table [\_SB_.SBA0.PCI0._PRT]
ACPI: PCI Root Bridge [PCI4] (00:80)
ACPI: PCI Interrupt Routing Table [\_SB_.SBA0.PCI4._PRT]
ACPI: PCI Root Bridge [PCI5] (00:a0)
ACPI: PCI Interrupt Routing Table [\_SB_.SBA0.PCI5._PRT]
ACPI: PCI Root Bridge [PCI6] (00:c0)
ACPI: PCI Interrupt Routing Table [\_SB_.SBA0.PCI6._PRT]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
GSI 16 (level, low) -> CPU 0 (0x0000) vector 49
ACPI: PCI interrupt 0000:00:00.0[A] -> GSI 16 (level, low) -> IRQ 49
GSI 38 (level, low) -> CPU 0 (0x0000) vector 50
ACPI: PCI interrupt 0000:a0:01.0[A] -> GSI 38 (level, low) -> IRQ 50
GSI 39 (level, low) -> CPU 0 (0x0000) vector 51
ACPI: PCI interrupt 0000:a0:01.1[B] -> GSI 39 (level, low) -> IRQ 51
GSI 40 (level, low) -> CPU 0 (0x0000) vector 52
ACPI: PCI interrupt 0000:a0:01.2[C] -> GSI 40 (level, low) -> IRQ 52
GSI 43 (level, low) -> CPU 0 (0x0000) vector 53
ACPI: PCI interrupt 0000:a0:02.0[A] -> GSI 43 (level, low) -> IRQ 53
GSI 42 (level, low) -> CPU 0 (0x0000) vector 54
ACPI: PCI interrupt 0000:a0:03.0[A] -> GSI 42 (level, low) -> IRQ 54
GSI 41 (level, low) -> CPU 0 (0x0000) vector 55
ACPI: PCI interrupt 0000:a0:04.0[A] -> GSI 41 (level, low) -> IRQ 55
GSI 49 (level, low) -> CPU 0 (0x0000) vector 56
ACPI: PCI interrupt 0000:c0:01.0[A] -> GSI 49 (level, low) -> IRQ 56
IOC: reserving 512Mb of IOVA space at 0x60000000 for agpgart
IOC: zx1 2.2 HPA 0xfed01000 IOVA space 1024Mb at 0x40000000
perfmon: version 2.0 IRQ 238
perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits)
PAL Information Facility v0.5
perfmon: added sampling format default_format
perfmon_default_smpl: default_format v2.0 registered
audit: initializing netlink socket (disabled)
audit(1118136648.422:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8BF2873F3985B5EB
- User ID: CentOS-4 (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THM0] (27 C)
EFI Time Services Driver v0.4
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: HP ZX1 IOC: IOPDIR shared with sba_iommu
agpgart: Maximum main memory to use for agp memory: 908M
agpgart: AGP aperture is 512M @ 0x60000000
agpgart: Detected HP ZX1 HWP0003 AGP chipset (ioc=fed01000, lba=fed20000)
i8042.c: i8042 controller self test timeout.
Serial: 8250/16550 driver $Revision: 1.90 $ 20 ports, IRQ sharing enabled
GSI 45 (edge, high) -> CPU 0 (0x0000) vector 57
ttyS0 at MMIO 0xff5e0000 (irq = 57) is a 16550A
GSI 46 (edge, high) -> CPU 0 (0x0000) vector 58
ttyS1 at MMIO 0xff5e2000 (irq = 58) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CMD649: IDE controller at PCI slot 0000:a0:02.0
ACPI: PCI interrupt 0000:a0:02.0[A] -> GSI 43 (level, low) -> IRQ 53
CMD649: chipset revision 2
CMD649: 100% native mode on irq 53
ide0: BM-DMA at 0xa0d0-0xa0d7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xa0d8-0xa0df, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
Using cfq io scheduler
ide1 at 0xa0e0-0xa0e7,0xa0f2 on irq 53
Probing IDE interface ide0...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EFI Variables Facility v0.08 2004-May-17
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 256Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 384kB freed
SCSI subsystem initialized
ACPI: PCI interrupt 0000:c0:01.0[A] -> GSI 49 (level, low) -> IRQ 56
sym0: <1010-66> rev 0x1 at pci 0000:c0:01.0 irq 56
sym0: using 64 bit DMA addressing
sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18j
Vendor: SEAGATE Model: ST336706LW Rev: 010A
Type: Direct-Access ANSI SCSI revision: 03
sym0:0:0: tagged command queuing enabled, command queue depth 16.
target0:0:0: Beginning Domain Validation
sym0:0: wide asynchronous.
sym0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target0:0:0: Ending Domain Validation
SCSI device sda: 71687370 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: SEAGATE Model: ST336706LW Rev: HPS1
Type: Direct-Access ANSI SCSI revision: 02
sym0:1:0: tagged command queuing enabled, command queue depth 16.
target0:0:1: Beginning Domain Validation
sym0:1: wide asynchronous.
sym0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
target0:0:1: Ending Domain Validation
SCSI device sdb: 71132960 512-byte hdwr sectors (36420 MB)
SCSI device sdb: drive cache: write through
sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.3.19-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:a0:03.0[A] -> GSI 42 (level, low) -> IRQ 54
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
divert: allocating divert_blk for eth0
Linux video capture interface: v1.00
ACPI: PCI interrupt 0000:a0:04.0[A] -> GSI 41 (level, low) -> IRQ 55
ACPI: PCI interrupt 0000:a0:01.2[C] -> GSI 40 (level, low) -> IRQ 52
ehci_hcd 0000:a0:01.2: EHCI Host Controller
ehci_hcd 0000:a0:01.2: irq 52, pci mem c0000000d0020000
ehci_hcd 0000:a0:01.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:a0:01.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:a0:01.0[A] -> GSI 38 (level, low) -> IRQ 50
ohci_hcd 0000:a0:01.0: OHCI Host Controller
ohci_hcd 0000:a0:01.0: irq 50, pci mem c0000000d0022000
ohci_hcd 0000:a0:01.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:a0:01.1[B] -> GSI 39 (level, low) -> IRQ 51
ohci_hcd 0000:a0:01.1: OHCI Host Controller
ohci_hcd 0000:a0:01.1: irq 51, pci mem c0000000d0021000
ohci_hcd 0000:a0:01.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 3-2: new full speed USB device using address 2
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
usb 3-2.3: new low speed USB device using address 3
input: USB HID v1.10 Keyboard [Lite-On Tech IBM USB Keyboard with UltraNav] on usb-0000:a0:01.1-2.3
input: USB HID v1.10 Device [Lite-On Tech IBM USB Keyboard with UltraNav] on usb-0000:a0:01.1-2.3
usb 3-2.4: new low speed USB device using address 4
input: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:a0:01.1-2.4
input: USB HID v1.00 Mouse [Synaptics Inc. Composite TouchPad / TrackPoint] on usb-0000:a0:01.1-2.4
NET: Registered protocol family 10
Disabled Privacy Extensions on device a000000100720e90(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
X(1883): unaligned access to 0x20000000005f03c3, ip=0x200000000034d610
X(1883): unaligned access to 0x20000000005f03c3, ip=0x200000000034d610
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
EXT3 FS on dm-0, internal journal
cdrom: open failed.
Adding 2031584k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
lp: driver loaded but no devices found
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
まあいくつか気になる点があるものの、起動はした。
足りない部分を補い、使い慣れているものを移植し、俺色にそめるのはこれからだ。
インストールするのが目的ではなく、普通のデスクトップPCとしてつかうのが目的だからな。
|
